102 lines
2.2 KiB
Arduino
102 lines
2.2 KiB
Arduino
|
#include <WiFi.h>
|
||
|
#include <WiFiClient.h>
|
||
|
#include <ArduinoOTA.h>
|
||
|
|
||
|
const char* host = "zpaesp32";
|
||
|
const char* ssid = "...";
|
||
|
const char* password = "...";
|
||
|
|
||
|
void setup() {
|
||
|
// put your setup code here, to run once:
|
||
|
Serial.begin(115200);
|
||
|
WiFi.mode(WIFI_STA);
|
||
|
|
||
|
WiFi.begin(ssid, password);
|
||
|
while (WiFi.waitForConnectResult() != WL_CONNECTED) {
|
||
|
Serial.println("Connection Failed! Rebooting...");
|
||
|
delay(5000);
|
||
|
ESP.restart();
|
||
|
}
|
||
|
|
||
|
ArduinoOTA
|
||
|
.onStart([]() {
|
||
|
String type;
|
||
|
if (ArduinoOTA.getCommand() == U_FLASH)
|
||
|
type = "sketch";
|
||
|
else // U_SPIFFS
|
||
|
type = "filesystem";
|
||
|
|
||
|
// NOTE: if updating SPIFFS this would be the place to unmount SPIFFS using SPIFFS.end()
|
||
|
Serial.println("Start updating " + type);
|
||
|
})
|
||
|
.onEnd([]() {
|
||
|
Serial.println("\nEnd");
|
||
|
})
|
||
|
.onProgress([](unsigned int progress, unsigned int total) {
|
||
|
Serial.printf("Progress: %u%%\r", (progress / (total / 100)));
|
||
|
})
|
||
|
.onError([](ota_error_t error) {
|
||
|
Serial.printf("Error[%u]: ", error);
|
||
|
if (error == OTA_AUTH_ERROR) Serial.println("Auth Failed");
|
||
|
else if (error == OTA_BEGIN_ERROR) Serial.println("Begin Failed");
|
||
|
else if (error == OTA_CONNECT_ERROR) Serial.println("Connect Failed");
|
||
|
else if (error == OTA_RECEIVE_ERROR) Serial.println("Receive Failed");
|
||
|
else if (error == OTA_END_ERROR) Serial.println("End Failed");
|
||
|
});
|
||
|
|
||
|
ArduinoOTA.begin();
|
||
|
|
||
|
Serial2.begin(300, SERIAL_7E1, 36, 4);
|
||
|
|
||
|
Serial.println("Test ZPA elektro");
|
||
|
|
||
|
|
||
|
Serial.println("Ready");
|
||
|
Serial.print("IP address: ");
|
||
|
Serial.println(WiFi.localIP());
|
||
|
|
||
|
}
|
||
|
|
||
|
void loop() {
|
||
|
// put your main code here, to run repeatedly:
|
||
|
ArduinoOTA.handle();
|
||
|
|
||
|
|
||
|
if (Serial2.available()) {
|
||
|
char r = Serial2.read();
|
||
|
|
||
|
if (r == 0x02) {
|
||
|
Serial.print("<STX>");
|
||
|
return;
|
||
|
}
|
||
|
|
||
|
if (r == 0x03) {
|
||
|
Serial.print("<ETX>");
|
||
|
return;
|
||
|
}
|
||
|
|
||
|
Serial.write(r);
|
||
|
}
|
||
|
|
||
|
|
||
|
if (Serial.available()) {
|
||
|
char r = Serial.read();
|
||
|
|
||
|
if (r == 'R') {
|
||
|
Serial.println("Requesting data");
|
||
|
Serial2.print("/?!\r\n");
|
||
|
return;
|
||
|
}
|
||
|
|
||
|
if (r == 'C') {
|
||
|
Serial.println("Trying change baudrate");
|
||
|
Serial2.write(0x06);
|
||
|
Serial2.print("030\r\n");
|
||
|
return;
|
||
|
}
|
||
|
|
||
|
Serial2.write(r);
|
||
|
}
|
||
|
|
||
|
}
|